Menu

Products

>

H52w AA Neutral White - LED headlamp
H52w AA Neutral White - LED headlamp
H52w AA Neutral White - LED headlamp
H52w AA Neutral White - LED headlamp

H52w AA Neutral White - LED headlamp$105.00 AUD

Out of stock

Main Features and Specifications

  • LED: Cree XM-L2 Neutral White (Nominal CCT 4400K)
  • User Selectable Levels: 3 main levels (High, Medium and Low). Each main level can be programmed to one of its two sub-levels. The second sub-level of the each main levels can be further programmed to different brightness levels.
  • Light Output (runtimes)
  • High: H1 280 Lm (0.9 hrs) or H2 172 Lm (1.7 hrs) / 108 Lm (3 hrs)
  • Medium: M1 50 Lm (7.5 hrs) or M2 25 Lm (12 hrs) / 12 Lm (27 hrs)
  • Low: L1 2.7 Lm (4 days) or L2 0.34 Lm (3 weeks) / 0.06 Lm (2 months) / 0.01 Lm (3 months)
  • Beacon Strobe Mode: 4Hz Strobe at H1 / 19Hz Strobe at H1
  • Light output are ANSI out the front (OTF) values. Runtimes tested (and parasitic drain estimated) using Sanyo 2000mAh Eneloop AA batteries. Light output with 14500 batteries are the same except that the H1 is 500Lm for the first minute and then step down to 280Lm.
  • Operating Voltage Range: 0.7V - 4.2V
  • Battery: One 1.5V AA (NiMH, lithium or alkaline) or 3.7V 14500 li-ion rechargeable. Batteries are not included in the package.
  • Parasitic Drain: Negligible (much less than the self discharging of a battery)
  • Beam Type:
  • 80 degree spill
  • 12 degree hot spot
  • Dimensions:
  • Head Diameter: 0.86 inch (21.8 mm)
  • Length: 3 inch (76.5 mm)
  • Weight
  • 1.1 oz (32 gram)
  • 2.0 oz (57 gram) with an Eneloop AA
  • 2.9 oz (80 gram) with an Eneloop AA and headband
Features:
Battery capacity indicator (LED flashes 1-4 times, 4 short clicks to start)
All levels are current regulated
Low battery alert when the light is switched Off (LED flashes if the battery voltage is below 1.06V)
Automatic stepping down to lower output when battery (AA and 14500) capacity is low
Builtin over-discharging protection for 14500 batteries at 2.8V cutoff
Durable electronic soft-touch switch
Smart user interface provides fast and easy access to all brightness levels and beacon-strobes.
Precision machined unibody casing from premium grade aluminum bar stocks
Proprietary heat sinking design bonds the LED board directly to the unibody aluminum casing
Durable natural hard anodized finish (Type III Class I)
Sealed and potted LED driver circuitry
Tempered optical grade glass
Battery power can be disconnected by slightly unscrewing the tailcap to prevent unwanted activations or parasitic drain
Waterproof to IPX7 (2 meters, 30 minutes)
Operations


This light has 3 main levels (High, Medium, and Low) and a beacon-strobe mode. Each main level can be programmed to one of its two sub-levels. The second sub-level of each main levels can be further programmed to different brightness levels.


Basic Operation
One short-click turns on the light to High or turns off the light.
Two short-click turns on the light to Medium.
Three short-click turns on the light to the beacon-strobe mode.
Press and hold (for over 0.6 seconds) turns on the light to Low and then Medium and High. Release at the desired level.
Advanced Operation and Configuration
Press and hold to cycle from Low, Medium and High, release at the desired level to set. When press and hold, the light always cycle from Low to High regardless which level you are currently in.
Double click to toggle and select between the two sub-levels for that main level. Sub-level selections for the 3 main levels are memorized after the light is turned off and through battery changes.
The second sub-level (H2, M2 and L2) of each main levels can be further programmed to different brightness levels. At a main level, double-click 6 times to start configuration. On subsequent double-clicks the light will cycle through different brightness levels. Short click to turn off the light when finishing configurations. The selections for the second sub-levels are memorized after the light is turned off and through battery changes.
This light uses the main LED (flashing 1 to 4 times) to indicate the estimated remaining capacity of the battery. To start the battery indicator, (from Off) short-click 4 times without pause.
Beacon-strobe mode can be accessed from 3 short-clicks when the light is Off. Once in the beacon-strobe mode, you can double-click to cycle through different types of beacons and strobes. Beacon-strobe settings are memorized when the light is turned off and through battery changes.

Accessories in the package:
Two o-rings
Pocket clip
One black silicone holder with headband

Customers who bought this item also bought...

GITD silicone holder for H51, H502, H52Revivex Durable WaterproofingReflective Glowire - 15metresTitanium nail pegsMini-D carabiner - wire gate

site managed by freesites